CONFIGURACION MODEM G.SHDSL LA11O + CONFIG CPE HUAWEI IPoA
FRAME RELAY
Router
* frame relay IETF
* LMI ANSI
* DLCI
Módem
* def data
- Application: Frame Relay
- CRC 16 bits
- T1.617 network (=ANSI)
* add conn data
- DLCI 16
_ VPI/VCI 0/35
_ Service interworking
- Active ON
- transparent
- PCR (calculado de acuerdo al BW)
* def network
- CPE
- 2 hilos
- Anexo A
* def clock
- Derived from the main link
NB
* Path
- (9/35 Interconexión DSLAM Morato - Alcatel 7670) vs (NB3645 A6-4 DLCI600)
- Annex D Network hacia el usuario
- Service interworking
- transparent
**************************************************************************************
CLEAR CHANNEL (64 Kbps)
Módem
* def data
- Application: AAL1 Stream
- Control Signal: C=Ignore , I=On / C=Obey , I = On
- BW (necesario)
* add conn data
- VPI/VCI
- Rx bytes/cell = 47
- Tx bytes/cell = 47
- Structured (without pointer) OJO!!!
* def network
- CPE
- 2 hilos
- Anexo A
* def clock: Derived from the main link
tipos de comandos
* para verificar
dsp conn data
* para borrar
del conn data
* Definer definirle algo.
def
*****************************************************************************
NB
* LO PASO A UNA ITERCONEXION CE EN BOG......
* Y DE ALLI UN VCC PATH HACIA EL STM1
*****************************************************************************
GESTIÓN
Módem
* def addr atm
- VPI/VCI
- Active = enable
- IP address = 1.1.1.2 30
- DHCP Client
- Bit Rate = UBR
- PCR
***************************************************************************
COMO ROUTER
Configuración módem RAD LA-110:
def password // para definir contraseña
Para configurar el password. El password anterior es 1234 y se le debe configurar CLIENTE
Adicionalmente, deshabilitar la opción de número de intentos antes de bloquearse, es decir, habilitar la opción NA
def clock // para definir el reloj del sistema
Verificar que esté seleccionada la opción seleccionada sea Derived from the main link.
def network // para definir la configuración de red
Cambiar la configuración del puerto G.SHDSL de ANNEX B a ANNEX A
Adicionalmente, asegurarse que esté configurado en modo CPE, no en CO.
add ip if
WAN
IP address
RFC 1483
VPI.VCI = 0.35
PCR = 171 cells/s (para un canal de 64 Kbps)
add ip if
LAN
IP address
def default gw
WAN (1)
Listo…
******************
EJ:>
STATIC ROUTING ADDRESS TABLE
============================
index IP Mask Metric Interface Nhop IP
-------------------------------------------------------------------------------
1 200. 21. 21. 0 255.255.255. 0 1 1 ----
2006-04-5T01:33:19
laboratorio>
laboratorio>dsp ip if
ETHERNET Interface
==================
Display mode : all
IP Interfaces
===============
Index IP Mask RIP Encapsulation Attached
-----------------------------------------------------------------------------
1 10. 0. 1. 2 255.255.255. 0 None RFC 1483 WAN 1
2 200. 21. 22. 1 255.255.255. 0 None Ethernet LAN 1
laboratorio>
*********************
COMANDOS PARA VERIFICIAR EL ESTADO DEL COBRE
********************
LA110> dsp pm network (ATT<10, SNR>30, PWR>12) para el estado del cobre.
LA110>def name
LA110>def data
********************
*********************
Trying X.X.200.29 ...
Press CTRL+K to abort
Connected to X.X.200.29 ...
Telnet Session is opened !
PASSWORD>*******
SUPERUSER MODE
LA110>DSP CONN DATA
*****************************************
MUESTRA LA CONFIGURACION
****************************************
FRAME RELAY Interface
=====================
Display mode : all
Inter- FR-SSCS- Cont
Index DLCI VPI.VCI DE->CLP CLP->DE working DLCI Check
-----------------------------------------------------------------------------
1 16 0. 36 convert convert service --- off-two way
2 17 0. 35 convert convert service --- off-two way
Bit Time-Since-
Index Mode FECN rate MDCR SCR PCR MBS Last-Change Active
-------------------------------------------------------------------------
1 translation convert UBR ---- ---- 1362 ---- 29:04:31 on
2 translation convert UBR ---- ---- 1362 ---- 29:04:31 on
6-2T05:01:35
Bad command or parameter. Type 'H' for help.
LA110>DSP DATA
FRAME RELAY Interface
=====================
Physical Interface: V35
Application : Frame Relay
Clock : DCE
Protocol : T1.617 network
CRC : 16 BIT
CLLM : no
Baud rate : 512k
Inverted Clock : Disable
2006-06-2T05:07:32
****************************************************************
BORRAR UN PVC UBR, PARA MODIFICACIONES CON TAB Y (F)
***************************************************************
LA110>DEL CONN DATA
Index : 1
Inter- FR-SSCS- Cont
Index DLCI VPI.VCI DE->CLP CLP->DE working DLCI Check
-----------------------------------------------------------------------------
1 16 0. 36 convert conv-DE-&-CLP network 16 off-two way
Bit Time-Since-
Index Mode FECN rate MDCR SCR PCR MBS Last-Change Active
-------------------------------------------------------------------------
1 ----- ----- UBR ---- ---- 1362 ---- 0:00:53 on
Index LB Operation LB Threshold LB Indication
--------------------------------------------------
1 off N/A N/A
Connection number 1 on data port was deleted
2006-06-2T05:08:05
*******************************************************
VERIFICAR QUE SE BORRARA EL PVC
*******************************************************
LA110>DSP CON DATA
Bad command or parameter. Type 'H' for help.
LA110>DSP CONN DATA
FRAME RELAY Interface
=====================
Display mode : all
Inter- FR-SSCS- Cont
Index DLCI VPI.VCI DE->CLP CLP->DE working DLCI Check
-----------------------------------------------------------------------------
2 17 0. 35 convert convert service --- off-two way
Bit Time-Since-
Index Mode FECN rate MDCR SCR PCR MBS Last-Change Active
-------------------------------------------------------------------------
2 translation convert UBR ---- ---- 1362 ---- 29:11:31 on
2006-06-2T05:08:35
*****************************************************
CREAR UN NUEVO PVC
*******************************************************
LA110>ADD CONN DATA
Adding connection number 1 to data port
DLCI VPI.VCI Interworking Active
---- ------- ------------ ------
18 0 .36 service on
FECN Mode DE<->CLP
---- ---- --------
convert transparent convert
Cont Check Bit-rate
---------- --------
off-two way VBR
PCR
---
1362
LB Operation LB Fail Threshold LB Fail Indication
------------ ----------------- ------------------
off N/A N/A
The connection was added successfully.
2006-06-2T05:11:00
************************************************************
VERIFICAR LA NUEVA CONFIGURACION
***********************************************************
LA110>DSP CONN DATA
FRAME RELAY Interface
=====================
Display mode : all
Inter- FR-SSCS- Cont
Index DLCI VPI.VCI DE->CLP CLP->DE working DLCI Check
-----------------------------------------------------------------------------
1 18 0. 36 convert convert service --- off-two way
2 17 0. 35 convert convert service --- off-two way
Bit Time-Since-
Index Mode FECN rate MDCR SCR PCR MBS Last-Change Active
-------------------------------------------------------------------------
1 transparent convert VBR ---- ---- 1362 ---- 0:00:21 on
2 translation convert UBR ---- ---- 1362 ---- 29:14:17 on
2006-06-2T05:11:21
LA110>
LA110>EXIT
*********************************************************************PARA MODIFICAR UN LA
LA110>def data
Physical Interface : V35
Application : Frame Relay
Protocol CRC
-------- ---
T1.617 network 16 BIT
Baud Inverted Clock
---- --------------
256k Disable
CLLM
----
no
**************
LA 110>mod conn data (los cambios se hacen con la tecla F)
Index : 1
Modifying connection number 1 on data port
DLCI : 16
VPI.VCI : 0.35
*******************************
*******************************
Jose Serrano dijo
Hola muy interesante tu blog, tengo una pregunta, de casualidad tendras la configuracion para la conexion de dos la-110 uno cpe y el otro CO, en modo bridge, mas que todo son las configuraciones logicas en la lan, los modem estan sincronizados pero no me pasan dta.
29 Julio 2009 | 07:58 AM